[Free] 2018(June) Ensurepass VMware VCP550 Dumps with VCE and PDF 51-60

Ensurepass.com : Ensure you pass the IT Exams
2018 May VMware Official New Released VCP550
100% Free Download! 100% Pass Guaranteed!

VMware Certified Professional on vSphere 5

Question No: 51 – (Topic 2)

A vSphere Standard Switch is configured with two uplinks.

When adjusting the failover order of the uplinks, what are two valid states in which an administrator can place the uplinks? (Choose two.)

  1. Active

  2. Unused

  3. Passive

  4. Disabled

Answer: A,B

Question No: 52 – (Topic 2)

– Exhibit –

Ensurepass 2018 PDF and VCE

– Exhibit –

Users accessing the WinXP virtual machine shown in the exhibit report intermittent connectivity to the corporate network.

The configuration is as follows:

  • This virtual machine runs in a DRS/HA cluster of two ESXi hosts.

  • The VCP_DCV_Example vSphere Distributed Switch was recently created.

  • The WinXP virtual machine was recently migrated from another vSphere Distributed Switch.

  • The WinXP virtual machine was able to connect prior to migration to this switch.

  • No changes to the VCP_DCV_Example switch have been made since creation.

    Which step should the administrator take to resolve the WinXP virtual machine#39;s intermittent connectivity to the corporate network?

    1. Add the ESXi host to the switch where the virtual machine is currently running

    2. Disable Port Blocking on the VCP_DCV_Example switch

    3. Disable Port Blocking on the Production port group

    4. Enable Network I/O Control on the switch to better balance I/O

    Answer: A

    Question No: 53 – (Topic 2)

    Why would an administrator be unable to locate an IP address for a vSphere vmnic uplink?

    1. IP addresses are defined at the virtual nic level, not the vmnic level.

    2. ESXi host vmnics communicate with physical switches on layer 3.

    3. ESXi hosts use NAT translation to mask the actual vmnic IP address.

    4. The IP address of the vmnic is not shown in the vSphere Client.

    Answer: A

    Question No: 54 – (Topic 2)

    A vSphere administrator needs to add redundancy to an ESXi 5.x management network on a vSphere Standard Switch.

    Which method should the administrator use to create redundant management networks?

    1. Configure the management network vSwitch with two active uplinks

    2. Configure an additional management portgroup on the same vSwitch

    3. Create a second management network on a second vSwitch in the same subnet

    4. Create a second management network on the same vSwitch in the same subnet

    Answer: A

    Question No: 55 – (Topic 2)

    Which two network settings are available on a vSphere Standard Switch? (Choose two.)

    1. Ingress traffic shaping

    2. Egress traffic shaping

    3. Private Virtual Local Area Networks (PVLAN)

    4. Virtual Local Area Networks (VLAN)

    Answer: B,D

    Question No: 56 – (Topic 2)

    – Exhibit –

    Ensurepass 2018 PDF and VCE

    – Exhibit –

    The vSphere administrator needs to remove the Production virtual machine port group from an ESXi host. The ESXi host#39;s Networking Configuration tab is shown in the exhibit.

    After disconnecting the Fileserver02 VM, what step does the administrator need to take, assuming that vSwitch1 will still be needed for further configuration?

    1. Remove the Production port group by accessing the properties for the port group.

    2. Remove the Production port group by accessing the properties for vSwitch1.

    3. Remove the Production port group by accessing the properties for the Network.

    4. Remove the Production port group by removing vSwitch1.

    Answer: B

    Question No: 57 – (Topic 2)

    An administrator is migrating 135 virtual machines from a vSphere Standard Switch to a vSphere Distributed switch. The migration reports an error and only some of the virtual machines are transferred.

    What is causing the error to occur?

    1. The vSphere Distributed Switch was created with a single, default port group.

    2. The switch has become disconnected from an ESXi host.

    3. The port group on the vSphere Distributed Switch was not configured with an Elastic port binding.

    4. The virtual machine that failed to transfer did not have a network adapter.

    Answer: A

    Question No: 58 – (Topic 2)

    Which VLAN configuration requires switch connectivity defined as an access port?

    1. Private VLAN

    2. External Switch Tagging

    3. Virtual Guest Tagging

    4. Virtual Switch Tagging

    Answer: B

    Question No: 59 – (Topic 2)

    – Exhibit –

    Ensurepass 2018 PDF and VCE

    – Exhibit –

    An administrator determines that traffic shaping does not appear to be working on Production, a virtual machine port group on vSwitch1. Traffic shaping is working on all other port groups on the switch.

    The administrator examines the Traffic Shaping settings as shown in the exhibit: What should the administrator do to resolve the problem?

    1. Select the Status checkbox to enable Traffic Shaping on the portgroup.

    2. Reduce the Average Bandwidth to 50% of the Peak Bandwidth.

    3. Reduce the Burst Size to 50% of the Peak Bandwidth.

    4. Click the Security tab and create the necessary security exception.

    Answer: C

    Reference: http://pubs.vmware.com/vsphere-55/topic/com.vmware.ICbase/PDF/vsphere- esxi-vcenter-server-55-networking-guide.pdf (page 94)

    Question No: 60 – (Topic 2)

    An organization is designing a new vSphere cluster to support a new product implementation.

    The following challenges have been identified by the vSphere administration team:

  • The organization has the vSphere Enterprise License.

  • The network team needs to gather virtual machine network statistics over a long period of time.

  • The network team needs the ability to quickly assess virtual machine traffic in the event of an attack.

  • The network team has previously had problems implementing manual etherchannel configurations on their physical switches, resulting in production outages.

  • The new cluster#39;s initial size is 15 hosts.

    The organization is willing to upgrade to vSphere Enterprise Plus licensing if it addresses these challenges.

    Which three features of a version 5.5 vSphere Distributed Switch would address these challenges? (Choose three.)

    1. LACP in Dynamic Mode

    2. Port Mirroring

    3. Network vMotion

    4. Private VLANs

    5. Network I/O Control

    Answer: A,B,C

    100% Ensurepass Free Download!
    Download Free Demo:VCP550 Demo PDF
    100% Ensurepass Free Guaranteed!
    VCP550 Dumps

    EnsurePass ExamCollection Testking
    Lowest Price Guarantee Yes No No
    Up-to-Dated Yes No No
    Real Questions Yes No No
    Explanation Yes No No
    PDF VCE Yes No No
    Free VCE Simulator Yes No No
    Instant Download Yes No No

  • Leave a Reply

    Your email address will not be published. Required fields are marked *

    This site uses Akismet to reduce spam. Learn how your comment data is processed.