[Free] 2017(Jan) EnsurePass Braindumps Juniper JN0-692 Dumps with VCE and PDF 11-20

Ensurepass.com : Ensure you pass the IT Exams
2017 Jan Juniper Official New Released JN0-692
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/JN0-692.html

Service Provider Routing and Switching Support, Professional

Question No: 11 – (Topic 1)

Click the Exhibit button.

Ensurepass 2017 PDF and VCE

Your router should be configured with a rewrite rule which alters the default behavior of expedited-forwarding as shown in the exhibit. Which configuration is correct?

Ensurepass 2017 PDF and VCE

  1. Option A

  2. Option B

  3. Option C

  4. Option D

Answer: A

Question No: 12 – (Topic 1)

You are facing BGP scaling issues and decide to add dedicated route reflectors to your network. You notice that VPN routes are not being advertised by your route reflectors. Which three actions can you take to solve this? (Choose three.)

  1. Add a static default route to inet.3 and/or inet6.3 on the route reflectors.

  2. Add a full mesh of MPLS LSPs between all of the route reflectors.

  3. Add MPLS LSPs between the route reflectors and their client routers.

  4. Add a static default route to inet.3 and/or inet6.3 on all of the client routers.

  5. Use rib-groups to add IGP routes to inet.3 and/or inet6.3 on the route reflectors.

Answer: A,C,E

Question No: 13 – (Topic 1)

Ensurepass 2017 PDF and VCE

Referring to the exhibit, which statement is true about the multicast state on R3?

  1. R3 has no PIM neighbors.

  2. R3 has no receivers.

  3. R3 has no route to RP.

  4. R3 is not receiving any traffic

Answer: D

Question No: 14 – (Topic 1)

Ensurepass 2017 PDF and VCE

You have been asked to troubleshoot an OSPF problem where the OSPF session will not establish.

According to the outputs shown in the exhibit, which statement is true?

  1. The hold-time interval is set too low.

  2. There is an MTU mismatch.

  3. The hold-time interval is set too high.

  4. The dead-interval is set too low.

Answer: B

Question No: 15 – (Topic 1)

Click the Exhibit button.

Ensurepass 2017 PDF and VCE

The IGP is IS-IS. Routes from R1 need to be present on R6. Referring to the exhibit, what will accomplish this task?

  1. Create an L1 adjacency between R2 and R3 to allow the routes to pass through to R6.

  2. Use policy on R3 to leak R1#39;s routes from L2 to L1.

  3. Change the area address from 49.0003 to 49.0001 on R6 to allow R6 to accept routes from R1.

  4. Use policy on R2 to leak R1#39;s routes from L1 to L2.

Answer: B

Question No: 16 – (Topic 1)

You have assigned target:65432:100 as the route target for Customer A#39;s BGP Layer 2 VPN. The PE1 router VRF is configured with vrf-target export target:65432:100.Which configuration on PE2 correctly assigned Customer A#39;s routes to their VRF?

  1. vrf-target target:65432:100

  2. route-target target:65432:100

  3. vrf-target export target:65432:100

  4. route-target export target:65432:100

Answer: A

Question No: 17 – (Topic 1)

Click the Exhibit button.

Ensurepass 2017 PDF and VCE

Referring to the OSPF link metrics in the exhibit, which path will traffic from R6 take to reach R1?

A. R6, R3, R2, R4, R1

B. R6, R3, R2, R1

C. R6, R5, R4, R1

D. R6, R5, R3, R2, R4, R1

Answer: B

Question No: 18 – (Topic 1)

Ensurepass 2017 PDF and VCE

Click the Exhibit button.

Traffic is flowing through the interfaces in the exhibit as follows:

On ge-0/0/2.0, IPv4 traffic has a throughput rate of 4 Mbps, and the burst size counter is at 200 KB.

On ge-0/0/2.0, IPv6 traffic has a throughput rate of 7 Mbps, and the burst size counter is at 550 KB.

On ge-0/0/3.0, IPv4 traffic has a throughput rate of 5 Mbps, and the burst size counter is at 250 KB.

On ge-0/0/3.1, IPv6 traffic has a throughput rate of 12 Mbps, and the burst size counter is at 450 KB.

Which statement describes what is happening?

  1. IPv6 traffic on ge-0/0.3.1 is being dropped; all other traffic is unaffected.

  2. IPv4 traffic on ge-0/0/2.0 is unaffected; IPv6 traffic on ge-0/0/2.0 is being dropped; IPv4 traffic on ge-0/0/3.0 is unaffected; IPv6 traffic on ge-0/0/3.1 is being dropped.

  3. IPv4 traffic on ge-0/0/2.0 is being dropped; IPv6 traffic on ge-0/0/2.0 is being dropped; IPv4 traffic on ge-0/0/3.0 is unaffected; IPv6 traffic on ge-0/0/3.1 is unaffected.

  4. All IPv4 and IPv6 traffic on ge-0/0/2 and ge-0/0/3 is being dropped.

Answer: B

Question No: 19 – (Topic 1)

R1 and R2 are IS-IS Level 1 routers, but are not forming an adjacency. Which two reasons would account for this happening? (Choose two.)

  1. The remote router is configured for both IPv4 and IPv6.

  2. The remote router does not have family iso enabled on its interface,

  3. The remote router does not have family clns enabled on its interface.

  4. The remote router is not configured to participate in the same Level 1 area

Answer: B,D

Question No: 20 – (Topic 1)

Ensurepass 2017 PDF and VCE

You are asked to configure an EBGP peering, but the peering does not establish and transitions between the Connect and Active states.

Referring to the exhibit, what is causing the problem?

  1. The number of messages from the BGP peer has exceeded the receive socket buffer.

  2. An incorrect local AS has been configured in the BGP group configuration.

  3. BGP is waiting to receive a keepalive or notification message from the peer.

  4. The BGP peer has an incorrect address configured, causing a connectivity failure.

Answer: D

100% Ensurepass Free Download!
Download Free Demo:JN0-692 Demo PDF
100% Ensurepass Free Guaranteed!
Download 2017 EnsurePass JN0-692 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 EnsurePass IT Certification PDF and VCE

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.